Press any key to end the test. The scanner goes into manual mode and starts receiving transmissions in the last channel. Note: Before using this feature, enter the local Skywarn frequency for your area into Bank 9, Channel The scanner has 10 channels for Skywarn: Bank 9, Channels Press or to select other Skywarn channels.
Press MAN to exit Skywarn. Note: If no frequencies are programmed in the Skywarn channels, No Prg appears and the scanner sounds an error tone. About Skywarn Skywarn is an organized group of trained weather observers. A Skywarn group exists in virtually every US County with a significant population.
Listen to Skywarn to hear trained observers in your vicinity call in official reports to a net control station which relays those reports to NOAA and other emergency agencies. Note: If you tune to a Skywarn frequency when the Skywarn net is not active, you may hear nothing, or you may hear amateur radio operators talking on a local repeater system. To avoid missing a reply on a specific channel, the scanner automatically programs a 2-second delay into any channel or frequency.
Depending on the scanner operation, follow one of these steps to turn the delay on or off. DLY disappears. DLY appears. DLY appears and the scanner automatically adds a 2-second delay to every frequency it stops on in that band.
The Signal Stalker I delay time is 10 seconds. When you turn off a bank, the scanner does not scan any of the 20 channels in that bank. While scanning, press the number key that corresponds to the bank you want to turn on or off.
The scanner scans all the channels within the displayed banks that are not locked out. If you try to turn off all banks, bank 0 remains. Locking Out Channels You can increase the scanning speed by locking out channels that have a continuous transmission such as a weather channel. Note: You can still manually select locked-out channels. Setting Priority The priority feature lets you scan through the channels and still not miss important or interesting calls on specific channels. You can program one stored channel in each bank as a priority channel.
The scanner checks the designated priority channel every two seconds in each bank. Press PRI during scanning to turn the priority feature on and off. PRI appears when priority is on. Note: If you have locked out all priority channels, All Loc appears when you activate the priority feature.
To select a different channel as the priority channel: 1. Press or to select the channel you want to set as priority, then press and hold PRI. Or, enter the bank and channel number you want to set as priority and then press PRI. P appears to the left of the selected channel frequency. Repeat Steps 1 and 2 for the channel in each bank that you want to program as a priority channel.
Using Keylock The keylock feature protects the scanner from accidental program changes. Using the Display Backlight To turn on the display light for easy viewing at night, press. The display lights for 15 seconds. Setting the Auto Backlight Display You can set the scanner so the backlight turns on for about 5 seconds when the scanner receives signals. If you press a key within the 5 seconds, the display remains lighted for 15 more seconds.
To turn auto backlight display on or off: 1. Setting the Power On Backlight The backlight can be set to light for 5 seconds when you power on the scanner. To turn the power on backlight on or off: 1. The scanner repeatedly turns off the internal power for one second, and then turns it back on for half a second to check for a transmission. To turn the battery save function on or off: 1. You can also upload or download programmed data from a PC through wired programming.
Turn on both scanners. WirEd and PGM appear. Press or on the scanner from which you want to send frequencies. SEnd and the transfer progress are displayed in the master unit. When the data transfer is completed, donE appears on both units. If the transfer was not successful, Error appears. After the clone operation is complete, remove the cable, turn both units off and then on again. Make sure your scanner is turned off. Install the software to your computer and run the program.
Turn the scanner on. The scanner automatically goes into the wired programming mode. When the scanner begins to communicate with the PC, PC flashes. PC stops flashing when the scanner has successfully received all data.
Turn the scanner off and remove the cable. Turn the scanner on again. To determine whether your scanner is causing the interference, turn off your scanner. If the interference goes away, your scanner is causing it. In some areas, mobile use of a scanner is unlawful or requires a permit. Check the laws in your area. Operation is subject ot the following two conditions: 1 This device may not cause harmful interference.
Scanning Legally Your scanner covers frequencies used by many different groups including police and fire departments, ambulance services, government agencies, private companies, amateur radio services, military operations, pager services, and wireline telephone and telegraph service providers.
It is legal to listen to almost every transmission your scanner can receive. However, there are some transmissions you should never intentionally listen to. This scanner is designed to prevent reception of illegal transmissions, in compliance with the law which requires that scanners be manufactured in such a way as to not be easily modifiable to pick up those transmissions.
Doing so could subject you to legal penalties. We encourage responsible, legal scanner use. Care Keep the scanner dry. If it gets wet, wipe it dry immediately.
Use and store the scanner only in normal temperature environments. Handle the scanner carefully; do not drop it. Keep the scanner away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new. Service and Repair If your scanner is not performing as it should, take it to your local RadioShack store for assistance. Specifications and depictions are subject to change and improvement without notice. Poor or no reception.
Error appears. Only one channel or no channels are stored. Scanner is not receiving power. The AC adapter or DC adapter is not connected. The keylock function is activated. Batteries are low. Batteries are weak or completely discharged. Antenna loose.
Programming error. Store frequencies into more than one channel. Recharge the rechargeable batteries or replace the non-rechargeable batteries. Recharge the rechargeable batteries or replace the alkaline batteries. Check the batteries or make sure the AC adapter or DC adapter is connected properly.
Make sure an antenna is connected to the scanner. Re-enter the frequency correctly, including the decimal point. Caution: This procedure clears all the information you have stored in the scanner. Before you reset the scanner, try turning it off and on again to see if it begins working properly. Status Not open for further replies. W0DER Member. Joined Jun 22, Messages 7. I am a little confused. The ARC page lists system requirements for programming the Pro and Pro including: "PC interface cable Radioshack or " Yet, the RS webpage for the does not include these in the list of supported radios.
Which is it? Or is there another cable that works? Anyone have any experience using software to program these units?
Which cable worked for you? Or something else? Joined May 28, Messages 2, I used the cable and the Butel ARC software to program it without any problem. I don't see why the newer wouldn't work - although I haven't personally tested the newer cable with those two scanners. Press to select On or OF. Setting the Power On Backlight The backlight can be set to light for 5 seconds when you power on the scanner. Page Setting The Battery Save Function Settings Setting the Battery Save Function The battery save feature conserves energy when the scanner is set to monitor a manually selected channel and it is not actively scanning.
The scanner repeatedly turns off the internal power for one second, and then turns it back on for half a second to check for a transmission. You can also upload or download programmed data from a PC through wired programming. When the data transfer is completed, appears on both units. If the transfer was not Error successful, appears. After the clone operation is complete, remove the cable, turn both units off and then on again. To determine whether your scanner is causing the interference, turn off your scanner.
If the interference goes away, your scanner is causing it. Page 35 Additional Information Antenna Impedance Only one channel Store frequencies into or no channels are more than one chan- stored. Caution: This procedure clears all the information you have stored in the scanner.
Before you reset the scanner, try turning it off and on again to see if it begins working properly. Page 38 Additional Information Notes Page 39 Additional Information Notes Page 40 RadioShack franchisees and dealers. For complete warranty details and exclusions, check with your local RadioShack store. This manual is also suitable for: Pro Print page 1 Print document 40 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account?
Sign up! Restore password.
0コメント